[Best Exam Dumps] Latest 100-105 Dumps Cisco Exam Training Materials And Study Guides Youtube Free Try

Lead4pass offers latest Cisco ICND1 100-105 dumps exam training materials and study guides free try from lead4pass. Get the best Cisco ICND1 100-105 dumps pdf files and dumps vce youtube update demo. https://www.lead4pass.com/100-105.html dumps pdf training resources. High quality Cisco ICND1 100-105 dumps exam practice questions and answers free download, pass Cisco 100-105 exam test easily.

Latest Cisco 100-105 dumps pdf training materials free download: https://drive.google.com/open?id=0B_7qiYkH83VReEJYRlhNVjdGeVU

Latest Cisco 300-101 dumps pdf training materials free download: https://drive.google.com/open?id=0B_7qiYkH83VRWFlVNGtTZjU1MVE

Vendor: Cisco
Certifications: ICND1
Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)
Exam Code: 100-105
Total Questions: 332 Q&As
100-105 dumps
QUESTION 1
The command ip route 192.168.100.160 255.255.255.224 192.168.10.2 was issued on a router. No routing protocols or other static routes are configured on the router. Which statement is true about this command?
A. The interface with IP address 192.168.10.2 is on this router.
B. The command sets a gateway of last resort for the router.
C. Packets that are destined for host 192.168.100.160 will be sent to 192.168.10.2.
D. The command creates a static route for all IP traffic with the source address 192.168.100.160.
Correct Answer: C

QUESTION 2
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC

QUESTION 3
Which statements are TRUE regarding Internet Protocol version 6 (IPv6) addresses? 100-105 dumps (Choose three.)
A. An IPv6 address is divided into eight 16-bit groups.
B. A double colon (::) can only be used once in a single IPv6 address.
C. IPv6 addresses are 196 bits in length.
D. Leading zeros cannot be omitted in an IPv6 address.
E. Groups with a value of 0 can be represented with a single 0 in IPv6 address.
Correct Answer: ABE

QUESTION 4
Why would a network administrator configure port security on a switch?
A. to prevent unauthorized Telnet access to a switch port
B. to prevent unauthorized hosts from accessing the LAN
C. to limit the number of Layer 2 broadcasts on a particular switch port
D. block unauthorized access to the switch management interfaces
Correct Answer: B

QUESTION 5
Refer to the exhibit.
100-105 dumps
Assume that all router interfaces are operational and correctly configured. In addition, assume that OSPF has been correctly configured on router R2. How will the default route configured on R1 affect the operation of R2?
A. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately.
B. Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur.
C. Any packet destined for a network that is not directly connected to router R1 will be dropped.
D. The networks directly connected to router R2 will not be able to communicate with the 172.16.100.0, 172.16.100.128, and 172.16.100.64 subnetworks.
E. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1.
Correct Answer: B

QUESTION 6
Refer to the exhibit.
100-105 dumps
If the resume command is entered after the sequence that is shown in the exhibit, 100-105 dumps which router prompt will be displayed?
A. Router1>
B. Router1#
C. Router2>
D. Router2#
Correct Answer: C

QUESTION 7
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following are required to solve this? (Choose three)
A. configure static frame relay map entries for each subinterface network.
B. remove the ip address from the physical interface
C. create the virtual interfaces with the interface command
D. configure each subinterface with its own IP address
E. disable split horizon to prevent routing loops between the subinterface networks
F. encapsulate the physical interface with multipoint PPP
Correct Answer: BCD

QUESTION 8
The ip helper-address command does what?
A. assigns an IP address to a host
B. resolves an IP address from a DNS server
C. relays a DHCP request across networks
D. resolves an IP address overlapping issue
Correct Answer: C

QUESTION 9
A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?
A. decrease the window size
B. use a different source port for the session
C. decrease the sequence number
D. obtain a new IP address from the DHCP server
E. start a new session using UDP
Correct Answer: A

QUESTION 10
What is one requirement for interfaces to run IPv6?
A. An IPv6 address must be configured on the interface.
B. An IPv4 address must be configured.
C. Stateless autoconfiguration must be enabled after enabling IPv6 on the interface.
D. IPv6 must be enabled with the ipv6 enable command in global configuration mode.
Correct Answer: A

QUESTION 11
Which two statements describe the process identifier that is used in the command to configure OSPF on a router? 100-105 dumps (Choose two.)
Router(config)# router ospf 1A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.
Correct Answer: CD

QUESTION 12
Some routers have been configured with default routes. What are some of the advantages of using default routes? (Choose two)
A. They establish routes that will never go down.
B. They keep routing tables small.
C. They require a great deal of CPU power.
D. They allow connectivity to remote networks that are not in the routing table
E. They direct traffic from the internet into corporate networks.
Correct Answer: BD

Reference: https://www.lead4pass.com/100-105.html dumps exam practice materials and study guides free update.

Watch the video to learn more: https://youtu.be/trVHfqmuVvg